Preparation and Reactivity of Core-Shell Al@CL-20 Composites Embedded with Graphene-Based Complexes as Catalysts.

Incomplete combustion of Al in solid propellants can be effectively resolved by coating of an oxidizer at the microscale. In this paper, Al@CL-20 composites with polydopamine as the interfacial layer were prepared using this strategy. The structure, heat of reaction, thermal decomposition properties, and combustion performances of these composites under the effects of graphene oxide (GO) and graphene-based carbohydrazide complexes (GO-CHZ-M, M = Co2+, Ni2+) have been comprehensively investigated. The experimental results show that the heat of reaction of Al@CL-20 is 6482 J g-1, which is 561 J g-1 higher than that of the corresponding mechanical mixture. The presence of GO-CHZ-Co can further increase the heat of reaction of Al@CL-20 to 6729 J g-1 with a decreased activation energy by about 54.8%. Under the synergistic effect of interfacial control and GO-CHZ-M, the ignition delay time of Al@CL-20-Co decreases from 5.1 to 4.2 ms. Besides, the D50 of the combustion condensed products (CCPs) decreased from 5.62 to 4.33 µm, indicating the combustion efficiency of Al is greatly improved.

Enhancing the Ignition and Combustion Performances of Solid Propellants Incorporating Al Particles Inside Oxidizers.

The combustion efficiency of Al plays a critical role in the combustion of high-energy aluminum-based solid propellants. For traditional formulations, the Al powders are dispersed in the binder matrix, leading to limited contact with the oxidizers and hence usually insufficient combustion and higher values of the pressure exponent. In this paper, various core-shell structural Al/oxidizer composites such as Al@HMX, Al@AP, and AP@Al have been prepared by a spray-drying technique based on which solid propellants with precise interfacial control between Al particles and oxidizers were realized. Compared to the control sample, the modified propellants have a greater heat of explosion of 5890 J g-1 (15% higher) and a reduced ignition delay time of 58 ms (65% decrease). Without changing the content of components, the burn rates of propellants can be easily modulated by tuning the interfacial contact of Al and oxidizers, where it varies in a wide range of 4.56-5.79 mm s-1 at the same pressure of 1 MPa. After introducing Al/oxidizer composites, the lowest pressure exponent of 0.19 within 1-15 MPa could be achieved by using Al@HMX and AP@Al composites. The agglomeration of Al was also inhibited by using Al/oxidizer composites, and the mechanism can be interpreted by using a classical "pocket" model. Moreover, the improved combustion efficiency of the solid propellants was verified by a noticeable reduction in the unreacted Al content.

High-Energy Composite Fuels with Improved Combustion Efficiency by Using AlH3 Embedded with Al Particles.

Aluminum hydride (AlH3) has attracted much attention due to its potential to replace aluminum (Al) as a novel energetic material in solid propellants. In this research, ammonium perchlorate (AP) and perfluoropolyether (PFPE) as functionalized coatings and a combination of acoustic resonance and spray drying technology have been employed to prepare AlH3@Al@AP (AHAPs) and AlH3@Al@AP@PFPE (AHAPs-F) energetic composite particles. The formulations of composite propellants and modified AlH3 particles were designed and fabricated. Their thermal reactivity, reaction heat, density, vacuum stability, combustion performance, and condensed combustion products (CCPs) have been systematically investigated. The results show that the solid propellants containing AHAPs (SP13) and AHAPs-F (SP14) composites can significantly enhance the reactivity and energy output compared to conventional solid propellants with the mechanical mixture Al/AlH3 (SP12). In particular, the total heat releases of SP13 and SP14 are almost 1.2 and 1.7 times higher than those of conventional ones (SP12, 1442 J g-1), respectively. Among the AlH3-based propellants, SP14 propellants exhibit the highest reaction heat of 5887 J g-1, the most intensive flame radiation of 31.4 × 103, and the highest combustion wave temperature of 2495 °C. Moreover, the particle size distribution of CCPs from SP14 propellants is much narrower and smaller than that of SP12, resulting in higher combustion efficiency.

Probing on Mutual Interaction Mechanisms of the Ingredients of Al/CuO/PVDF Nanocomposites.

In this paper, several binary and ternary metastable intermixed nanocomposites Al/CuO, Al/PVDF, CuO/PVDF, and Al/CuO/PVDF have been prepared by simple mechanical mixing and ball milling followed by spray drying methods. In this way, the interfacial structure could be well tuned and compared in terms of reactivity. The nonisothermal DSC curves results showed that the exothermic reaction of Al/CuO/PVDF could be divided into three steps. In addition, it has been shown that for the same formulation, the reaction efficiency, pressurization capacity, and thermal reactivity are greatly dependent on the interfacial structure. As a typical example, composite Al@PVDF/CuO, where Al is fully covered with PVDF, exhibited a higher energy release of 10.7 kJ·cm-3 and pressurization rates of 22.79 MPa·s-1·g-1. The reaction between Al and PVDF has been facilitated in both extent of reaction and efficiency due to their intimate contact. Based on the thermal analysis, condensed combustion product analysis, and gaseous phase identification, the mutual reaction mechanisms of Al/CuO/PVDF have been proposed. The most likely reactions that occurred at each stage of the reaction are summarized, providing insight into the complicated underlying mechanisms. It shows that the regulation of energy release rates and improved efficiency could be easily realized by predesigned interfacial structures.

Precise Regulation of Combustion Characteristics of High-Energy Composite Propellants by Incorporation of CL-20 Crystals Intercalated with Energetic Burn Rate Modifiers.

In this study, a 2D structured triaminoguanidine-glyoxal polymer with a high nitrogen content has been coordinated with metal ions to produce energetic metal complexes (TAGP-Ms) employed as energetic burn rate inhibitors. The metal ions (Ba2+, K+, and Ca2+) are elaborately selected based on their ability of suppressing the burn rate of composite propellants. The CL-20 crystals were intercalated with prepared TAGP-Ms materials via a solvent-antisolvent method for realization of the precise control on burning behaviors of studied propellants. The influence of TAGP-Ms inhibitors on thermal decomposition and combustion characteristics of high-energy composite propellants was evaluated using thermal analysis and a combustion diagnostic method. Results of TGA/DSC-FTIR measurements suggest that the thermal decomposition of CL-20-containing composite propellants was found to be constrained by varied degrees as a result of TAGP-Ms additions, in which the TAGP-K displays a stronger effect on suppressing the thermal decomposition of CL-20 compared with that of other TAGP-Ms. The FTIR spectra indicate that the primary gaseous phase products are composed of N2O, H2O, and CO2 in CL-20 decomposition, as well as by HCl, H2O, NO2, and N2O in the decomposition of AP for all studied composite propellants. The combustion characterizations show that the TAGP-K-containing composite propellant exhibits a significantly reduced rate of heat release but is associated with a higher flame radiation intensity increased by 4.2% compared with that of the reference propellant, which clearly implies that the TAGP-K is capable of suppressing the energy release rate while ensuring the high energetic features of propellants to be well maintained. Moreover, the burn rate pressure exponents are considerably decreased by ∼10% for the TAGP-K-containing propellants in comparison with those of propellants with the typical formulation, which strongly suggests that TGAP-Ms are promising candidates for tuning the combustion behaviors of composite propellants by influencing the decomposition processes of CL-20 and AP collectively.

Thermal Reactivity of High-Density Hybrid Hexahydro-1,3,5-trinitro-1,3,5-triazine Crystals Prepared by a Microfluidic Crystallization Method.

In this paper, the two-dimensional (2D) high nitrogen triaminoguanidine-glyoxal polymer (TAGP) has been used to dope hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) crystals using a microfluidic crystallization method. A series of constraint TAGP-doped RDX crystals using a microfluidic mixer (so-called controlled qy-RDX) with higher bulk density and better thermal stability have been obtained as a result of the granulometric gradation. The crystal structure and thermal reactivity properties of qy-RDX are largely affected by the mixing speed of the solvent and antisolvent. In particular, the bulk density of qy-RDX could be slightly changed in the range from 1.78 to 1.85 g cm-3 as a result of varied mixing states. The obtained qy-RDX crystals have better thermal stability than pristine RDX, showing a higher exothermic peak temperature and an endothermic peak temperature with a higher heat release. Ea for thermal decomposition of controlled qy-RDX is 105.3 kJ mol-1, which is 20 kJ mol-1 lower than that of pure RDX. The controlled qy-RDX samples with lower Ea followed the random 2D nucleation and nucleus growth (A2) model, whereas controlled qy-RDX with higher Ea (122.8 and 122.7 kJ mol-1) following some complex model between A2 and the random chain scission (L2) model.

Stabilization of AlH3 Crystals by the Coating of Hydrophobic PFPE and Resulted Reactivity with Ammonium Perchlorate.

Aluminum hydride (AlH3) is a promising fuel component of solid propellant, but its stabilization is still challenging. Herein, surface functionalization of hydrophobic perfluoropolyether (PFPE) followed by ammonium perchlorate (AP) coating has been implemented. In particular, AlH3@PFPE@xAP (x = 10, 30, 50, or 64.21%) composites (AHFPs) were prepared by a spray-drying technique. The PFPE-functionalized AlH3 with a hydrophobic surface shows an increased water contact angle (WCA) from 51.87° to 113.54°. Compared with pure AlH3, the initial decomposition temperatures of AHFPs were increased by 17 °C, and the decomposition properties of AP in the AHFPs were also enhanced with significantly decreased peak temperature and fairly increased energy output. Moreover, the decomposition induction time of AHFPs-30% was improved by almost 1.82 times that of raw AlH3, which indicates that the coatings of PFPE and AP could improve the stability of AlH3. The maximum flame radiation intensity of AHFPs-30% was 21.6 × 103, which is almost 7.71 times that of pure AlH3 (2.8 × 103).

Graphene Oxide-Intercalated Tetrazole-Based Coordination Polymers: Thermally Stable Hybrid Energetic Crystals with Enhanced Photosensitivity.

High-energy-density photosensitive pyrotechnics with good thermal stability have been in increasing demand in recent years. In this paper, graphene oxide (GO)-intercalated energetic coordination polymers (ECPs) are prepared with improved thermostability but great photosensitivity by using high nitrogen compounds azotetrazole (AT) and 5,5'-bistetrazole-1,1'-diolate dehydrate (BTO) as ligands. The decomposition activation energy (Ea) of Cu-AT has been increased from 135.7 to 151.9 kJ·mol-1 after intercalating 5 wt% GO, and in the meantime, the exothermic peak temperature (Tp) was increased by 12.6 °C. However, the decomposition Ea of Cu-BTO decreased under the effect of the same amount of GO with little effect on Tp. This confirms that GO has stabilization effects on the Cu-AT crystal, whereas the catalytic effects on Cu-BTO would dominate after dehydration with its crystal lattice collapse. Also, when the content of GO was 3%, the resultant GO0.03-Cu-AT exhibits a higher density (2.88 g·cm-3) and good thermostability (Tp = 293.7 °C). This ECP shows excellent low-energy laser ignition performance, which can be ignited with an energy of less than 1 mJ at a wavelength of 976 nm. Low-energy laser initiation is considered to be a safer but more reliable method than the traditional electrical-based ones.

Modulation of Crystal Growth of an Energetic Metal-Organic Framework on the Surfaces of Graphene Derivatives for Improved Detonation Performance.

Energetic materials are a special class of energy materials composed of C, H, O, and N. Their safety always deteriorates with increasing energy. Regulating the properties of energetic materials to meet application requirements is one of the focuses of research in this field. Energetic metal-organic frameworks (EMOFs) are good candidates as primary explosives to replace lead azide (LA) and other explosives containing toxic metal elements. However, safety remains the biggest concern in applications. In this paper, crystal morphology modulation of EMOF was carried out by stepwise coordination of metal ions and energetic ligands on surfaces of graphene oxide (GO) and amino-functionalized graphene oxide (AGO). Two energetic composite materials, Cu-AFTO@GO and Cu-AFTO@AGO, were successfully synthesized and also the EMOF (Cu-AFTO). The structures and morphologies of these materials were fully characterized. The thermal decomposition behaviors, mechanical sensitivity, and electrostatic discharge sensitivity were investigated in detail. The electric ignition ability of EMOF and two composite materials was tested. This study shows that it is possible to reduce the diameter of EMOF crystals from hundreds of microns to tens of nanometers by a stepwise coordination method. The high electrical conductivity and sensitivity-reducing effect of GO and/or AGO allow the nanosized EMOF crystals to have a lower ignition threshold and lower sensitivity.

Enhanced thermal and energetic properties of NC-based nanocomposites with silane functionalized GO.

The surface functionalization of graphene oxide (GO) is always attractive in improving certain properties of the polymer. In this study, 3-aminopropyltriethoxysilane (APTES) and 3-mercaptopropyl-trimethoxysilane (SPTES) have been used to make silane functionalized graphene oxides (SiGOs). The APTES-grafted GO (NH-SiGO), SPTES-grafted GO (SH-SiGO) and pure GO have been separately introduced into the nitrocellulose (NC) matrix. The morphology, thermal properties and energetic properties of the prepared nanocomposites (NH-SiGO and SH-SiGO) were investigated comprehensively. It is shown that the presence of GO and SiGOs have different influences on the thermal reactivity of NC with various contents, and NH-SiGO with 0.5 wt% content showed better catalytic performance on the thermal decomposition of NC than others and showed prominently higher efficiency in improving its heat of combustion. Adding 0.5 wt% of NH-SiGO to NC may decrease its decomposition temperature from 202.1 °C to 196.6 °C, and the residue was decreased from 10.61 wt% to 3.95 wt%, respectively. One isoconversional kinetic method was exploited to determine the kinetic parameters of NC and its nanocomposites. It was found that NH-SiGO had a strong catalytic action on the thermal decomposition of NC-based nanocomposites for which the activation energy and the pre-exponential factor were considerably lowered, while SH-SiGO exhibited an inverse effect. The heat of combustion from NC/GO/0.5, NC/NH-SiGO/0.5 and NC/SH-SiGO/0.5 were determined as 11 249.5, 11 675.1 and 11 491.5 J g-1, respectively, which are higher than that of the pure NC (10 908.4 J g-1). From the combustion process of NC/NH-SiGO/0.5, it was shown that the nanocomposite was combusted completely.

Preparation of CNTs Coated with Polydopamine-Ni Complexes and Their Catalytic Effects on the Decomposition of CL-20.

To improve the condensed-phase reaction rate of ε-CL-20, polydopamine (PDA)-nickel complex-coated multiwalled carbon nanotubes (CNTs) have been prepared and used as combustion catalysts. The PDA-Ni complex has been prepared and in situ coprecipitated with ε-CL-20 by an antisolvent crystallization process in its dimethyl sulfoxide (DMSO) solution. It has been shown that crystalline CL-20 composites included with PDA-Ni complexes are polygon-shaped with a smooth surface and an average diameter of 10-15 µm, whereas it is 140 µm for raw ε-CL-20 crystals. The catalytic reactivity of the complex on thermolysis of CL-20 has been investigated using the differential scanning calorimetry (DSC) and thermogravimetry (TG)-coupled Fourier transform infrared (FT-IR) spectroscopy technique. It has been found that CNT@PDA-Ni complexes have catalytic effects on the decomposition of ε-CL-20 by decreasing/shifting of the exothermic peak from T p = 240.1 to 238.7 °C. The FT-IR spectra of CL-20 decomposition products under the effect of the catalyst predominantly show peaks at 1274, 1644 and 1596, 1912, 2265, and 1956-1800 cm-1, indicating the presence of fragments with N2O, NO2, NO, HNCO, and NO/CO, respectively. The change in the ε-CL-20 decomposition mechanism should be attributed to the catalytic action of CNT, decreasing the formation of NO2. Also, under the effect of the carbon-based catalyst, the HNCO formation was detected at another temperature in comparison with raw CL-20, with peak absorption at 224.1 vs 232.3 °C and the evolution was completed at 250.8 vs 246.2 °C, respectively.

Hybrid RDX crystals assembled under constraint of 2D materials with largely reduced sensitivity and improved energy density.

In this paper, the widely used energetic material RDX had been modified with 2D high nitrogen polymer (TAGP). Various hybrid RDX crystals (qy-RDX) with higher detonation velocity and better thermostability had been obtained as a result of strong intermolecular interactions between TAGP and RDX molecules. The performance of the qy-RDX had been characterized to clarify the inherent mechanisms. It shows that the⊿Hf of qy-RDX could be largely changed in the range of 23.4 kJ kg-1 to 1343.6 kJ kg-1, whereas the density varies only from 1.81 g cm-3 to 1.86 g cm-3. The resulted detonation velocities are in the range of 8725.5 m·s-1 to 9251.8 m·s-1, depending on the content and state of the TAGP dopant. The sensitivity of the resulted qy-RDX is much better than pristine RDX due to improved crystal quality as well as higher concentration of hydrogen bonds. The impact energy is improved from 8.5 J (RDX) to 22 J (qy-RDX-1), whereas the friction sensitivity improves form 130 N to over 360 N for the same case. The Ea for thermal decomposition of qy-RDX-1has reduced from 147.8 kJ mol-1 (RDX) to (124.5 kJ mol-1), since TAGP dopant could be considered as active catalytic sites after melting of RDX.

Gaseous Products Evolution Analyses for Catalytic Decomposition of AP by Graphene-Based Additives.

A quantitative evaluation method has been developed to study the effects of nanoadditives on thermal decomposition mechanisms of energetic compounds using the conventional thermogravimetry coupled with mass spectrometry (TG/MS) technique. The decomposition of ammonium perchlorate (AP) under the effect of several energetic catalysts has been investigated as a demonstration. In particular, these catalysts are transition metal (Cu2+, Co2+ and Ni2+) complexes of triaminoguanidine (TAG), using graphene oxide (GO) as dopant. They have been well-compared in terms of their catalytic effects on the concentration of the released gaseous products of AP. These detailed quantitative analyses of the gaseous products of AP provide a proof that the proton transfer between O and O2 determines the catalytic decomposition pathways, which largely depend on the type of reactive centers of the catalysts. This quantitative method could be applied to evaluate the catalytic effects of any other additives on the thermal decomposition of various energetic compounds.

Transformation of Combustion Nanocatalysts inside Solid Rocket Motor under Various Pressures.

In this paper, the dependences of the morphology, particle sizes, and compositions of the condensed combustion products (CCP) of modified double-base propellants (1,3,5-trimethylenetrinitramine (RDX) as oxidizer) on the chamber pressure (<35 MPa) and nickel inclusion have been evaluated under a practical rocket motor operation. It has been shown that higher pressure results in smaller average particle sizes of the CCPs. The CCPs of Ni-containing propellants have more diverse morphologies, including spherical particles, large layered structures, and small flakes coated on large particles depending on the pressure. The specific surface area (SSA) of CCPs is in the range of 2.49 to 3.24 m² g-1 for propellants without nickel are less dependent on the pressure, whereas it is 1.22 to 3.81 Ni-based propellants. The C, N, O, Al, Cu, Pb, and Si are the major elements presented on the surfaces of the CCP particles of both propellants. The compositions of CCPs from Ni-propellant are much more diverse than another one, but only three or four major phases have been found for both propellants under any pressure. The metallic copper is presented in CCPs for both propellants when the chamber pressure is low. The lead salt as the catalyst has been transformed in to Pb(OH)Cl as the most common products of lead-based catalysts with pressure lower than 15 MPa. When pressure is higher than 5 MPa, the nickel-based CCPs has been found to contain one of the following crystalline phases: Pb2Ni(NO2)6, (NH4)2Ni(SO4)2·6H2O, C2H2NiO4·2H2O, and NiO, depending on the pressure.

Thermal behavior of graphene oxide and its stabilization effects on transition metal complexes of triaminoguanidine.

The graphene oxide (GO) was found to be able to stabilize organic molecules including energetic compounds. However, the inherent mechanisms of such stabilization effects are still not well-known. Herein, various transition metal complexes of triaminoguanidine nitrate (TAGN) using GO as a dopant have been prepared and evaluated. It has been shown that the presence of GO could great improve the thermal stability of the resulted TAG-based complexes. The physical models governing their thermolysis for their initial rate-limiting decomposition steps are obtained using the state-of-the-art evaluation methods. These physical models are further supported by analyses of the overall gaseous products. In addition, the reaction pathways are proposed to explain the stabilization mechanisms of GO. For instance, by interaction of GO, the release of N2 from TAG-Ni was greatly postponed. There is a broad secondary peak at temperature of 378 °C due to decomposition of the nickel nitrides, as the primary thermolysis intermediates of TAG-Ni. The formation of cobalt nitrides plays a significant role on decomposition of TAG-Co and G-T-Co, which results in much less heat release and mass loss in comparison to TAG-Ni.

Reaction kinetics and a physical model of the charring layer by depositing Al2O3 at ultra-high temperatures.

The thermochemical ablation of insulation material caused by slag deposition in solid rocket motors has increasingly attracted researchers' attention. Understanding the ablation mechanism and the ability to calculate reaction kinetics parameters determine the height of the thermal protection design for advanced solid rocket motors. In this work, the interaction of the Al2O3-C system is determined through static ablation experiments. Using X-ray diffraction, HSC thermodynamic software, and a thermogravimetric analyser, the carbon thermal reduction of alumina is analysed and the reaction mechanism and physical model are obtained. Isothermal experiments at 1700-1850 °C and mathematical analysis provide the kinetic parameters of the overall and step-by-step reactions. The results show that the overall reaction of the Al2O3-C system involves three steps. The overall reaction kinetics are described by the contracting area model R2 with apparent activation and frequency factors estimated as 254.5 kJ mol-1 and 5.5 × 106 min-1, respectively. The distribution reaction kinetics of steps 1 and 2 are described by the first-order chemical reaction control model (F1) and that of step 3 is described by the one-dimensional diffusion control model (D1). The corresponding activation energies are 107.9 kJ mol-1, 240.3 kJ mol-1, and 567.5 kJ mol-1, and frequency factors are 625.94 min-1, 8.3 × 105 min-1, and 1.6 × 1014 min-1, respectively.

Tuning the Reactivity of Metastable Intermixed Composite n-Al/PTFE by Polydopamine Interfacial Control.

The metastable intermixed composite (MIC) is one of the most popular research topics in the field of energetic materials (EMs). The goal is to invent EMs with tunable reactivity and desired energy content. However, it is very difficult to tune the reactivity of MIC due to its high reactivity and sensitivity caused by enlarged specific surface area and intimate contact between the oxidizers and fuels. Herein, we demonstrated a facile fabrication method that can be used to control the reactivity between the nanoaluminum (n-Al) and poly(tetrafluoroethylene) (PTFE) using an in situ-synthesized polydopamine (PDA) binding layer. It was found that PDA can adhere to both n-Al and PTFE particles, resulting in integrated n-Al@PDA/PTFE MICs. In comparison with traditional n-Al/PTFE MICs, the n-Al@PDA/PTFE showed an increased energy release and reduced sensitivity and more importantly tunable reactivity. By regulating the experimental conditions of coating, the thickness of PDA could be well controlled, which makes the tunable reactivity of n-Al@PDA/PTFE possible. The PDA interfacial layer may increase the preignition reaction (PIR) heat of Al2O3/PTFE and therefore the overall reaction heat of n-Al/PTFE. It also reveals that the PDA interfacial layer postponed the PIR, leading to an increase in onset thermal decomposition temperature ( To). As To increased, a more complete reaction between PTFE and Al nanoparticles could be achieved.

Highly Reactive Metastable Intermixed Composites (MICs): Preparation and Characterization.

Highly reactive metastable intermixed composites (MICs) have attracted much attention in the past decades. The MIC family of materials mainly includes traditional metal-based nanothermites, novel core-shell-structured, 3D ordered macroporous-structured, and ternary nanocomposites. By applying special fabrication approaches, highly reactive MICs with uniformly dispersed reactants, "layer-by-layer" or "core-shell" structures, can be prepared. Thus, the combustion performance can be greatly improved, and the ignition characteristics and safety can be precisely controlled by using a certain preparation strategy. Here, the preparation and characterization of the MICs that have been developed during the past few decades are summarized. Traditional preparation methods for MICs generally include physical mixing, high-energy ball milling, sol-gel synthesis, and vapor deposition, while the novel methods include self-assembly, electrophoretic deposition, and electrospinning. Various preparation procedures and the ignition and combustion performance of different MIC reactive systems are compared and discussed. In particular, the advantages of novel structured MICs in terms of safety and combustion efficiency are clarified, based on which suggestions regarding the possible future research directions are proposed.

Formation of Highly Thermostable Copper-Containing Energetic Coordination Polymers Based on Oxidized Triaminoguanidine.

A series of novel highly thermostable energetic coordination polymers (ECPs), with promising mechanical sensitivity properties, were prepared by an in situ oxidation-coordination reaction of triaminoguanidine hydrochloride with copper nitrate in aqueous solution. The molecular structures and properties of these ECPs could be tuned, by varying the ratios and concentrations of the starting materials. Our ECPs exhibit remarkable thermostability (>390 °C) and very low sensitivity to impact (Im > 98 J). The best-performing material (ECP-5) has a calculated detonation velocity of 8969 m·s(-1) and a decomposition peak temperature of 396.9 °C, demonstrating an outstanding balance between two inherently contradicting properties: high detonation performance and very low sensitivity.

Highly energetic compositions based on functionalized carbon nanomaterials.

In recent years, research in the field of carbon nanomaterials (CNMs), such as fullerenes, expanded graphite (EG), carbon nanotubes (CNTs), graphene, and graphene oxide (GO), has been widely used in energy storage, electronics, catalysts, and biomaterials, as well as medical applications. Regarding energy storage, one of the most important research directions is the development of CNMs as carriers of energetic components by coating or encapsulation, thus forming safer advanced nanostructures with better performances. Moreover, some CNMs can also be functionalized to become energetic additives. This review article covers updated preparation methods for the aforementioned CNMs, with a more specific orientation towards the use of these nanomaterials in energetic compositions. The effects of these functionalized CNMs on thermal decomposition, ignition, combustion and the reactivity properties of energetic compositions are significant and are discussed in detail. It has been shown that the use of functionalized CNMs in energetic compositions greatly improves their combustion performances, thermal stability and sensitivity. In particular, functionalized fullerenes, CNTs and GO are the most appropriate candidate components in nanothermites, solid propellants and gas generators, due to their superior catalytic properties as well as facile preparation methods.